The above shows my home-built digital clock. It uses Nixie-tubes for readout. In contrast to most other nixie-clocks being built these days, my clock does not use any transistor or IC for driving the tubes. Instead, the driving logic is built from neon lamps, together with resistors, capacitors and silicon diodes.
The project started in 2002, when
our university library was
selling old outdated or otherwise superfluous books, and I very cheaply
bought the book "Electronic Counting Circuits"
by J.B. Dance, published in 1967, and apparently only ever lent
three times by our library, all in 1973.
It described how neon lamps can be used as logic elements in a ring counter,
exploiting the fact that they need
a higher voltage to ignite (the striking voltage)
than to stay lit (the maintaining voltage):
Unfortunately, if one substitutes the neon bulbs that are available in electronics shops nowadays, the circuit doesn't work. Dance used lamps that were specifically manufactured for this type of application, with a large difference between their striking and maintaining voltages. Nowadays, such lamps are (presumably) no longer manufactured; the neon bulbs that are still available in shops are meant as indicator lamps, and have a much smaller difference between their striking and maintaining voltages. This required changing the circuit's resistor values, and makes its operation more critical; furthermore, the lamps need to be selected for matching characteristics.
This is one of the ring counters in my clock:
Four of these are used, to divide the 50 Hz from the mains power (see here for stability measurements) first by 10 (yielding 5 Hz), then by 5 (yielding 1 Hz, i.e., one pulse per second), then further by 10 and 6 to yield one pulse per minute. Note the paper labels still dangling at the cathode wires of the lamps: these are needed to look up the measured properties of each lamp.
Four more ring counters are used dividing by 10, 6, 10 and 3, to count
the minutes, tens-of-minutes, hours and tens-of-hours
and drive the Nixie tubes:
The nixie tubes are driven through Light Dependent Resistors (LDRs): under the influence of the light from the neon lamp, their resistance lowers, connecting one nixie cathode to the negative power supply. In order for the LDR not to be influenced too much by ambient light, while still allowing the neon bulb to be visible, an optical attenuator and filter is used between them, consisting of a black cardboard disk with a small hole in it, and two layers of red foil, held together by glue and shrink tube:
The ring counters are rather sensitive to ambient light: in complete darkness,
they tend not to work. Even though there are always a few bulbs active (if only
in the power supply, which is not shown in the photographs), my clock
still needs a bit of external ambient light.
I'm experimenting with blue LEDs for providing this extra ambient light.
This seems to be quite effective: illuminated by just two blue leds,
the clock ran perfectly one night long in otherwise complete darkness:
Note though that the blue in this photo is more intense than it looks like in reality: apparently the camera is more sensitive to this shade of blue than the human eye.
Some other things that I ran into while designing this clock:
The clock is now electrically functional, but still some work remains to be done. The power supply needs to be built tidily, the aligator clip test leads eliminated, and the whole thing put into a (transparent) enclosure for safety.
A short movie (AVI format, 10 MB) of the clock in operation is available here.
Furthermore, the circuit diagram is available in a PDF file. This schematic diagram contains some extra explanation of how specific parts work. This diagram is meant to document and explain the details of my clock, and there will probably be some minor changes made in the future. The diagram is not meant as a complete basis for building another such clock; for example, while some of the resistor values are quite uncritical and determined by what I happened to have at hand, many depend critically on the characteristics of the neon lamps used. (Hopefully needless to say, any prospective builders should take proper safety precautions for working with the high voltages involved.)
Comments are welcome at firstname.lastname@example.org.
Copyright © 2007.
Back to my amateur radio webpage.